This page is part of archived documentation for openHAB 4.1. Go to the current stable version
PH-PSG01 Smoke Sensor
This describes the Z-Wave device PH-PSG01, manufactured by Zipato with the thing type UID of zipato_phpsg01_00_000.
The device is in the category of Smoke Detector, defining Smoke detectors.
The PH-PSG01 supports routing. This allows the device to communicate using other routing enabled devices as intermediate routers. This device is unable to participate in the routing of data from other devices.
The PH-PSG01 does not permanently listen for messages sent from the controller - it will periodically wake up automatically to check if the controller has messages to send, but will sleep most of the time to conserve battery life. Refer to the Wakeup Information section below for further information.
Overview
Zipato Smoke Sensor (Z-Wave) is designed to give early warning of developing fires by giving off the alarm sounds from its build-in alarm horn, based on Z-Wave technology. Zipato Smoke Sensor is Z-Wave Plus product, it supports security, OTA and all other new features of 500 Series Z-Wave chipset.
Inclusion Information
- Have Z-Wave Controller entered inclusion mode.
- Press test button three times within 1.5 seconds to enter the inclusion mode.
- After the adding was successful, the device will wake to receive the setting from Z-Wave Controller about 20 seconds.
Exclusion Information
- Have Z-Wave Controller entered inclusion mode.
- Pressing test button three times within 1.5 seconds to enter the exclusion mode. Node ID has been removed.
Wakeup Information
The PH-PSG01 does not permanently listen for messages sent from the controller - it will periodically wake up automatically to check if the controller has messages to send, but will sleep most of the time to conserve battery life. The wakeup period can be configured in the user interface - it is advisable not to make this too short as it will impact battery life - a reasonable compromise is 1 hour.
The wakeup period does not impact the devices ability to report events or sensor data. The device can be manually woken with a button press on the device as described below - note that triggering a device to send an event is not the same as a wakeup notification, and this will not allow the controller to communicate with the device.
After device is added to the network, it will wake-up once per day by default.When it wakes-up it will broadcast the “Wake Up Notification” message to the network, and wake-up 10 seconds to receive the setting commands. The wake-up interval minimum setting is 30 minutes, and maximum setting is 120 hours. Interval step is 30 minutes. If you want to wake-up device immediately, please press the button once. The device will wake-up for 10 seconds.
General Usage Information
Factory reset:
Notice: Use this procedure only in the event that the primary controller is lost or otherwise inoperable.
- Have Z-Wave Controller entered inclusion mode.
- After the red LED flash 9 times, release the test button within 2 seconds.
- IDs are removed and all settings will reset to factory default.
Channels
The following table summarises the channels available for the PH-PSG01 -:
| Channel Name | Channel ID | Channel Type | Category | Item Type |
|---|---|---|---|---|
| switch | switch_binary | switch_binary | Switch | Switch |
| Binary Sensor | sensor_binary | sensor_binary | Switch | |
| Alarm temperature | alarm_tamper | alarm_tamper | Switch | |
| Battery Level | battery-level | system.battery_level | Battery | Number |
| Alarm smoke | alarm_smoke | alarm_smoke | Smoke | Switch |
switch
Switch the power on and off.
The switch_binary channel is of type switch_binary and supports the Switch item and is in the Switch category.
Binary Sensor
Indicates if a sensor has triggered.
The sensor_binary channel is of type sensor_binary and supports the Switch item. This is a read only channel so will only be updated following state changes from the device.
The following state translation is provided for this channel to the Switch item type -:
| Value | Label |
|---|---|
| ON | Triggered |
| OFF | Untriggered |
Alarm temperature
Indicates if the tamper alarm is triggered.
The alarm_tamper channel is of type alarm_tamper and supports the Switch item. This is a read only channel so will only be updated following state changes from the device.
The following state translation is provided for this channel to the Switch item type -:
| Value | Label |
|---|---|
| OFF | OK |
| ON | Alarm |
Battery Level
Represents the battery level as a percentage (0-100%). Bindings for things supporting battery level in a different format (e.g. 4 levels) should convert to a percentage to provide a consistent battery level reading.
The system.battery-level channel is of type system.battery-level and supports the Number item and is in the Battery category.
This channel provides the battery level as a percentage and also reflects the low battery warning state. If the battery state is in low battery warning state, this will read 0%.
Alarm smoke
Indicates if a smoke is triggered.
The alarm_smoke channel is of type alarm_smoke and supports the Switch item and is in the Smoke category. This is a read only channel so will only be updated following state changes from the device.
The following state translation is provided for this channel to the Switch item type -:
| Value | Label |
|---|---|
| OFF | OK |
| ON | Alarm |
Device Configuration
The following table provides a summary of the 2 configuration parameters available in the PH-PSG01. Detailed information on each parameter can be found in the sections below.
| Param | Name | Description |
|---|---|---|
| 7 | Customer Function | Customer Function |
| 10 | Auto Report Battery Time | Auto Report Battery Time |
| Wakeup Interval | Sets the interval at which the device will accept commands from the controller | |
| Wakeup Node | Sets the node ID of the device to receive the wakeup notifications |
Parameter 7: Customer Function
Customer Function Notification type 0: Using Notification Report 1: Using Sensor Binary Report Values in the range 0 to 4 may be set.
The manufacturer defined default value is 4.
This parameter has the configuration ID config_7_1 and is of type INTEGER.
Parameter 10: Auto Report Battery Time
Auto Report Battery Time The interval time for auto report the battery level. Values in the range 0 to 127 may be set.
The manufacturer defined default value is 127.
This parameter has the configuration ID config_10_1 and is of type INTEGER.
Wakeup Interval
The wakeup interval sets the period at which the device will listen for messages from the controller. This is required for battery devices that sleep most of the time in order to conserve battery life. The device will wake up at this interval and send a message to the controller to tell it that it can accept messages - after a few seconds, it will go back to sleep if there is no further communications.
This setting is defined in seconds. It is advisable not to set this interval too short or it could impact battery life. A period of 1 hour (3600 seconds) is suitable in most instances.
Note that this setting does not affect the devices ability to send sensor data, or notification events.
This parameter has the configuration ID wakeup_interval and is of type INTEGER.
Wakeup Node
When sleeping devices wake up, they send a notification to a listening device. Normally, this device is the network controller, and normally the controller will set this automatically to its own address. In the event that the network contains multiple controllers, it may be necessary to configure this to a node that is not the main controller. This is an advanced setting and should not be changed without a full understanding of the impact.
This parameter has the configuration ID wakeup_node and is of type INTEGER.
Association Groups
Association groups allow the device to send unsolicited reports to the controller, or other devices in the network. Using association groups can allow you to eliminate polling, providing instant feedback of a device state change without unnecessary network traffic.
The PH-PSG01 supports 1 association group.
Group 1: Lifeline
The Lifeline association group reports device status to a hub and is not designed to control other devices directly. When using the Lineline group with a hub, in most cases, only the lifeline group will need to be configured and normally the hub will perform this automatically during the device initialisation.
Association group 1 supports 8 nodes.
Technical Information
Endpoints
Endpoint 0
| Command Class | Comment |
|---|---|
| COMMAND_CLASS_SWITCH_BINARY_V1 | |
| COMMAND_CLASS_SENSOR_BINARY_V2 | |
| COMMAND_CLASS_ASSOCIATION_GRP_INFO_V1 | |
| COMMAND_CLASS_DEVICE_RESET_LOCALLY_V1 | |
| COMMAND_CLASS_ZWAVEPLUS_INFO_V2 | |
| COMMAND_CLASS_CONFIGURATION_V1 | |
| COMMAND_CLASS_ALARM_V1 | |
| COMMAND_CLASS_MANUFACTURER_SPECIFIC_V2 | |
| COMMAND_CLASS_POWERLEVEL_V1 | |
| COMMAND_CLASS_FIRMWARE_UPDATE_MD_V2 | |
| COMMAND_CLASS_BATTERY_V1 | |
| COMMAND_CLASS_WAKE_UP_V2 | |
| COMMAND_CLASS_ASSOCIATION_V1 | |
| COMMAND_CLASS_VERSION_V2 | |
| COMMAND_CLASS_SECURITY_V1 | |
| COMMAND_CLASS_SENSOR_ALARM_V1 |
Documentation Links
Did you spot an error in the above definition or want to improve the content? You can contribute to the database here.